/*
* ========== Copyright Header Begin ==========================================
* 
* OpenSPARC T2 Processor File: n2_err_siu_dmu_trap.s
* Copyright (C) 1995-2007 Sun Microsystems, Inc. All Rights Reserved
* 4150 Network Circle, Santa Clara, California 95054, U.S.A.
*
* DO NOT ALTER OR REMOVE COPYRIGHT NOTICES OR THIS FILE HEADER. 
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
*
* For the avoidance of doubt, and except that if any non-GPL license 
* choice is available it will apply instead, Sun elects to use only 
* the General Public License version 2 (GPLv2) at this time for any 
* software where a choice of GPL license versions is made 
* available with the language indicating that GPLv2 or any later version 
* may be used, or where a choice of which version of the GPL is applied is 
* otherwise unspecified. 
*
* Please contact Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, 
* CA 95054 USA or visit www.sun.com if you need additional information or 
* have any questions. 
*
* 
* ========== Copyright Header End ============================================
*/
#define H_HT0_Hw_Corrected_Error_0x63 My_Corrected_ECC_error_trap
#define H_HT0_Sw_Recoverable_Error_0x40  My_Recoverable_Sw_error_trap


    
/* #define MAIN_PAGE_NUCLEUS_ALSO */ /* Access main in priviledge mode */
#define MAIN_PAGE_HV_ALSO

#include "err_defines.h"
#include "hboot.s"
#include "peu_defines.h"
!#include "dmu_peu_regs.h"

#define CFG_RD_ADDR mpeval(N2_PCIE_BASE_ADDR + IOCFG_OFFSET_MASK_REG_DATA)
#define CFG_RD_DATA 64'h33323130


/************************************************************************
   Test case code start
 ************************************************************************/
.text
.global main
.global  My_Corrected_ECC_error_trap
.global  My_Recoverable_Sw_error_trap

main:
        ta T_CHANGE_HPRIV
        nop

#include "peu_init.h"
!
! Thread 0 Start
!
!
thread_0:
CONFIGURE_NCU_FOR_PCIE_TRAFFIC:
        setx    IOCFG_OFFSET_BASE_REG_ADDR, %g1, %g2
        setx    IOCFG_OFFSET_BASE_REG_DATA, %g1, %g3
        stx     %g3, [%g2]
        nop
        ldx     [%g2], %g4
        nop

        setx    IOCFG_OFFSET_MASK_REG_ADDR, %g1, %g2
        setx    IOCFG_OFFSET_MASK_REG_DATA, %g1, %g3
        stx     %g3, [%g2]
        nop
        ldx     [%g2], %g4
        nop

	! enable bypass in IOMMU
	setx	FIRE_DLC_MMU_CSR_A_CTL_ADDR, %g1, %g2
	setx	FIRE_DLC_MMU_CSR_A_CTL__BYPASS_EN, %g1, %g3
	stx	%g3, [%g2]
	ldx	[%g2], %g3


set_ejr:
        set     0x1, %i1
        sllx    %i1, ERR_FIELD, %i2
        setx    SOC_EJR_REG, %l7, %i3
        stx     %i2, [%i3]
        membar  0x40

eie_reg_ones:
        setx    SOC_EIE_REG, %l7, %g5
        stx     %i2, [%g5]
        membar  0x40

	
XmtUsrEvnt:
	nop         ! $EV trig_pc_d(1, @VA(.MAIN.XmtUsrEvnt)) -> EnablePCIeIgCmd ("DMAWR", IOMMU_BYP_SADDR, IOMMU_BYP_SADDR, 64'h40, 64'd1 )

XmtCmd:
	! select a CFG address in PCI address range and transmit the command to NCU
	setx CFG_RD_ADDR, %g1, %g2
	nop
	
	setx	FIRE_PLC_TLU_CTB_TLR_CSR_A_TLU_CTL_ADDR, %g1, %g2
	setx	0x020, %g1, %g4


delay_loop:
	ldx	[%g2], %g5
	nop
	nop
	nop
	nop
	dec	%g4
	brnz	%g4, delay_loop
	nop

        ! ESR is cleared in INT
	! but the next error causes it to log again;
	! Get from Uday a diag which has just 1 DMA

/*
check_esr:
        setx    SOC_ESR_REG, %l7, %i0
        ldx     [%i0], %i1
!        sub     %i1, %g0, %i5
!        brnz    %i5, test_failed
!        nop

        setx    0x8000000000000000, %l7, %o3    !valid bit
        set     0x1, %i2
        sllx    %i2, ERR_FIELD, %i3
        or      %i3, %o3, %i4
        sub     %i1, %i4, %i5
        brnz    %i5, test_failed
        nop
*/

check_per:
        setx    SOC_PER_REG, %l7, %i0
        ldx     [%i0], %i1
        nop

        sub     %i1, %i4, %i5
        brnz    %i5, test_failed
        nop


  ! Check if a Corrected ECC Trap happened
check_error_trap:
        setx  EXECUTED, %l1, %l0
        cmp   %o6, %l0
        bne   test_failed
        nop
        mov   TT, %l0
        cmp   %o7, %l0
        bne   test_failed
        nop

        setx    SOC_ESR_REG, %l7, %i0
        ldx     [%i0], %i1
        nop

        setx    0x8000000000000000, %l7, %o3    !valid bit
        set     0x1, %i2
        sllx    %i2, ERR_FIELD, %i3
        or      %i3, %o3, %i4
        sub     %i1, %i4, %i5
        brnz    %i5, test_failed
        nop

	
test_passed:
	EXIT_GOOD

test_failed:
	EXIT_BAD




/************************************************************************
   Trap Handlers
 ************************************************************************/
My_Recoverable_Sw_error_trap:
        ! Signal trap taken
        setx  EXECUTED, %l0, %o6
        ! save trap type value
        rdpr  %tt, %o7
        retry
        nop

My_Corrected_ECC_error_trap:
        ! Signal trap taken
        setx  EXECUTED, %l0, %o6
        ! save trap type value
        rdpr  %tt, %o7
        retry
        nop

/************************************************************************
   Test case data start
 ************************************************************************/

/************************************************************************/