Initial commit of OpenSPARC T2 design and verification files.

[OpenSPARC-T2-DV] / verif / diag / diaglists / ccu / ccu.diaglist

// ========== Copyright Header Begin ==========================================
// 
// OpenSPARC T2 Processor File: ccu.diaglist
// Copyright (C) 1995-2007 Sun Microsystems, Inc. All Rights Reserved
// 4150 Network Circle, Santa Clara, California 95054, U.S.A.
//
// * DO NOT ALTER OR REMOVE COPYRIGHT NOTICES OR THIS FILE HEADER. 
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; version 2 of the License.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
// 
// For the avoidance of doubt, and except that if any non-GPL license 
// choice is available it will apply instead, Sun elects to use only 
// the General Public License version 2 (GPLv2) at this time for any 
// software where a choice of GPL license versions is made 
// available with the language indicating that GPLv2 or any later version 
// may be used, or where a choice of which version of the GPL is applied is 
// otherwise unspecified. 
//
// Please contact Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, 
// CA 95054 USA or visit www.sun.com if you need additional information or 
// have any questions. 
// 
// ========== Copyright Header End ============================================
<sys(ccu_clk_ratios) name=sys(ccu_clk_ratios)>
<sys(all)>
<sys(daily)>

 <fc_ccu_166>  // fc bench: default is 166mhz sys clk

  <runargs -config_cpp_args=-DIDT_AMB>                          // build with IDT AMB model
  <runargs -midas_args=-DCMP_THREAD_START=0x1 -finish_mask=1>   // single thread (ie. thread 0)
  <runargs -midas_args=-DRESET_STAT_CHECK>                      // must specify this option when doing WMR reset
  <runargs -nofast_boot -vcs_run_args=+NO_CCU_CSR_SLAM -midas_args=-DCCU_REG_PROG -midas_args=-DWARM_RESET_INIT>
  <runargs -sas -midas_args=-DBOOTPROM_INIT>
  <runargs -vcs_run_args=+SSI_CLK_4 -vcs_run_args=+show_delta>
  <runargs -vcs_run_args=+mcu_errmon_disable -vcs_run_args=+mcu_fmon_disable -vcs_run_args=+l2esr_mon_off>
  <runargs -vcs_run_args=+ccu_checker>
     memop_all_atomics_CMPDR_RATIO_2_00_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_2_00
     memop_all_atomics_CMPDR_RATIO_2_25_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_2_25
     memop_all_atomics_CMPDR_RATIO_2_50_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_2_50
     memop_all_atomics_CMPDR_RATIO_2_75_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_2_75
     memop_all_atomics_CMPDR_RATIO_3_00_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_3_00
     memop_all_atomics_CMPDR_RATIO_3_25_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_3_25
     memop_all_atomics_CMPDR_RATIO_3_50_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_3_50
     memop_all_atomics_CMPDR_RATIO_3_75_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_3_75
     memop_all_atomics_CMPDR_RATIO_4_00_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_4_00
     memop_all_atomics_CMPDR_RATIO_4_25_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_4_25
     memop_all_atomics_CMPDR_RATIO_4_50_sysclk166	memop_all_atomics.s -midas_args=-DCMPDR_RATIO_4_50
  </runargs>
  </runargs>
  </runargs>
  </runargs>
  </runargs>
  </runargs>
  </runargs>
  </runargs>

</fc_ccu_166>

//---- Add these groups/regressions if needed -----
// <fc_ccu_133>  // NOTE: requires fsr's rtl and IDT AMB model, so put them 
// </fc_ccu_133> //       in a separate file (ie. ccu_sysclk133.diaglist)
// <fc_ccu_200>  // NOTE: fc bench does not support 200mhz sys clk yet.
// </fc_ccu_200>


</sys(daily)>
</sys(all)>
</sys(ccu_clk_ratios)>